PTFE Cold Flow and Creep in Seals and Machined Parts

Published Updated Technical author

PTFE cold flow is time-dependent dimensional change under sustained load below the material’s melting temperature. In seals, bushings, washers and machined parts, it can reduce contact pressure, alter clearances or move a component outside its intended tolerance. Risk depends on grade, filler, stress, temperature, geometry, confinement and time. It cannot be controlled by machining tolerance alone; material selection, load distribution, support and validation under the actual operating conditions must be considered together.

This guide explains what cold flow and creep mean, why they matter in real components, how virgin and filled PTFE differ, and which information helps a manufacturer recommend a more dimensionally stable solution. It is intended as a practical engineering and purchasing reference, not as a substitute for validation under the actual pressure, temperature, medium and assembly conditions.

What are PTFE cold flow and creep?

Cold flow describes permanent deformation that can occur when PTFE is loaded below its melting temperature. Creep is the time-dependent continuation of that deformation under a sustained load. The terms are often used together in PTFE discussions because the practical result is similar: a part can gradually move away from its original dimensions while it remains compressed, clamped or loaded.

This behavior does not automatically mean the material is unsuitable. It means the part geometry, confinement, stress level, temperature, grade and expected service time must be considered together. A correctly supported PTFE seal can perform very differently from an unsupported part exposed to the same nominal load.

Why can PTFE deform at room temperature?

PTFE polymer chains can rearrange slowly under stress. The rate and magnitude of deformation depend on several interacting variables:

  • Applied stress: higher continuous stress generally increases deformation risk.
  • Temperature: elevated temperature normally accelerates creep and reduces the margin against extrusion.
  • Time: a part that looks stable after assembly may continue to change during long-term service.
  • Geometry and support: thin sections, sharp transitions and unsupported edges behave differently from confined sections.
  • Material grade: virgin PTFE and filled grades have different stiffness, wear and creep characteristics.
  • Surface and mating parts: roughness, gaps, fastener distribution and thermal expansion affect local stress.

Where PTFE creep creates problems

ComponentPossible effectDesign question
Gaskets and washersLoss of gasket stress, reduced sealing load or edge extrusionIs the gasket sufficiently confined, and can the joint maintain compression?
Bushings and bearingsChange in running clearance, ovality or local wearWhat are the radial load, speed, temperature and shaft finish?
Valve seats and sealsProfile distortion or movement into a clearance gapWhat pressure direction, cycling and anti-extrusion support are present?
Machined rings and insulatorsDimensional drift after machining or assemblyWhich dimensions are functional, and when will inspection take place?
Sheet liners and padsLocal thinning or material movement around fastenersHow is the load distributed and how is the sheet restrained?

Virgin PTFE versus filled PTFE for dimensional stability

Virgin PTFE is preferred when chemical purity, electrical properties, low friction or broad chemical compatibility dominate the specification. When creep resistance, stiffness or wear life is more important, a filled PTFE grade may be considered. The best filler depends on the operating environment; there is no single filled grade that is best for every application.

Material optionTypical engineering objectiveImportant checks
Virgin PTFEPurity, chemical resistance, electrical insulation and low frictionConfinement, continuous stress, temperature and allowable dimensional change
Glass-filled PTFEImproved stiffness, wear resistance and reduced deformation in many mechanical usesChemical medium, counterface and filler percentage
Carbon-filled PTFEWear performance, stiffness and improved response in selected dynamic applicationsElectrical behavior, mating surface and fluid compatibility
Graphite-filled PTFELow-friction behavior and sealing or sliding performanceLoad, speed, lubrication and target leakage performance
Bronze-filled PTFEHigh wear resistance and improved dimensional stability for selected mechanical partsCorrosive media, weight, mating material and electrical requirements
Black cylindrical PTFE bushings with through-bores on a wooden surface
Custom machined filled PTFE bushings. Filler selection, tolerances and final dimensions should be matched to load, temperature and assembly clearance.

Pengrowth processes glass-fiber, carbon-fiber, graphite, molybdenum-disulfide, bronze, anti-static and wear-modified PTFE grades. The resin source, filler type and filler ratio should be confirmed for the specific duty rather than selected only from a generic data table. See our filled PTFE machined parts and custom machined PTFE parts capabilities.

Seven design strategies to reduce PTFE creep risk

  1. Reduce unnecessary continuous stress. Avoid using assembly force to compensate for an unsuitable geometry. Calculate the load actually carried by the PTFE section.
  2. Provide mechanical support. Confinement, backing rings, shoulders and controlled clearances can limit material movement.
  3. Avoid thin unsupported edges. Thin lips and abrupt section changes can concentrate stress and encourage extrusion or distortion.
  4. Select the grade from the duty. Compare virgin and filled PTFE using temperature, medium, motion, counterface and electrical requirements—not stiffness alone.
  5. Allow for thermal expansion. PTFE changes dimension more with temperature than many metals. Assembly clearances must account for the full operating range.
  6. Define functional tolerances. Identify which dimensions control sealing, fit or movement. Over-tight tolerances on non-functional dimensions add cost without solving creep.
  7. Validate the assembled system. A material datasheet cannot reproduce the exact joint, load history, pressure cycling or mating-surface condition.

Machining, tolerance and inspection considerations

PTFE can move during machining, cooling, storage and final assembly. Dimensional control therefore begins before the last cutting pass. Material conditioning, balanced stock removal, tool sharpness, fixturing pressure and inspection timing all influence the measured result.

Achievable tolerances are confirmed after reviewing geometry, material, functional dimensions and the inspection method.

The quotation and approved inspection plan should define the applicable incoming-material checks, process-check frequency, semi-finished and final inspections, any sample performance tests, and packing and traceability records. Their scope is order-specific; a fixed two-hour inspection frequency is not established here. A drawing-based quotation should identify the measurement temperature, datum structure and critical fit dimensions.

Troubleshooting PTFE parts that lose dimensional stability

Observed issueLikely factors to investigatePossible direction
Gasket loses sealing loadExcessive compression, temperature, insufficient confinement or uneven flange loadingReview gasket stress, joint stiffness, surface condition and grade
Bushing clearance closesThermal expansion, radial load, wall thickness or moisture/temperature measurement differenceRecalculate running clearance and consider a more stable filled grade
Ring becomes oval after machiningResidual stress, unbalanced machining or weak fixturing methodUse staged machining, controlled clamping and defined inspection timing
Seal extrudes into a gapPressure, temperature, clearance gap and unsupported edgeAdd support or anti-extrusion geometry and review the compound
Dimensions vary between inspection and assemblyTemperature, storage condition, measurement method or datum inconsistencyAgree inspection conditions and functional measurement points

Information to send for a PTFE creep-resistant part quotation

  • Part drawing or ID, OD, thickness, length and critical tolerances
  • Continuous and peak temperature
  • Pressure, compressive load or bearing load
  • Chemical medium and concentration
  • Static or dynamic operation, speed and cycle frequency
  • Mating material, surface finish and clearance
  • Virgin or filled PTFE preference, if already specified
  • Prototype and production quantity
  • Current failure mode, such as leakage, extrusion, wear or dimensional drift

For sheet-based components, review our PTFE sheet options. For a drawing review, prototype or material recommendation, send the application conditions to Pengrowth. Sample availability, cost and shipping conditions are confirmed during RFQ review. Sample and production lead times are confirmed after reviewing material, dimensions, process, quantity and inspection requirements.

Frequently asked questions

Does all PTFE cold-flow under load?

All PTFE grades are viscoelastic, but the amount and rate of deformation vary with material, filler, stress, temperature, time and geometry. Proper confinement and grade selection can greatly improve dimensional stability.

Is filled PTFE always better than virgin PTFE?

No. Filled PTFE can improve stiffness, wear or creep resistance, but fillers can change chemical, electrical, friction and counterface behavior. Virgin PTFE remains the correct choice for many purity, insulation and chemical-service applications.

Can machining tolerance prevent creep?

Tolerance controls the initial manufactured dimension; it does not remove time-dependent material behavior. The drawing, material grade, support geometry and operating conditions must be reviewed together.

What should be tested before production?

For critical applications, validate the assembled component under representative temperature, load, pressure, medium and cycle conditions. A prototype or small batch can confirm fit and identify where the drawing needs adjustment.

Engineering references